1.2 inches on a ruler

1.2 inches on a ruler is 3.048 cm, 30.48 mm and 1.2 inches from zero. The blue line on the left ruler ends at that length.

Ölçek hazırlanıyor.

Rest the object on the zero line. Hover the ruler, or drag on the blank area to measure between two points.

Hover the ruler or drag to measure.

Ruler diagram

Ruler diagram of 1.2 in. The blue band runs from zero to this mark: at the 1 3/16 inch division.
This picture is a reading diagram, not a true centimetre on the screen. Calibrate the ruler above for real size.

Where 1.2 in sits on the ruler

The blue band runs from zero to this mark. If it passes the screen, scroll the horizontal ruler. A narrow phone does not shrink the scale; the mark simply sits further along. The left ruler stays fixed as soon as the page opens.

1.2 in is 3/16 inch past the 1 inch line, which reduces to 1 3/16. The shortest gap is 1/16 inch (1.59 mm). The total is 30.48 mm, or 3.048 cm.

This value does not land on a 1/16 line. The nearest division is 1 3/16, off by 0.32 mm.

1.2 in fits on a 15 cm school ruler. The spare length is 11.95 cm on a 15 cm ruler, 16.95 cm on a 20 cm ruler, and 26.95 cm on a 30 cm ruler.

1.2 in is close to the width of a thumbnail; nails vary, the ruler mark does not. The long side of a mini-SIM is 25 mm; this length is 5.48 mm longer.

1.2 in is 3.05 percent of a metre. A 1 metre strip yields 32 whole pieces, with 24.64 mm left over.

the length of an AA battery (5.05 cm) is 1.66 times this length. 1.2 in fits 1 times, with 2 cm left over.

In CSS, 1 inch is 96 pixels. 1.2 in is about 115.2 pixels. The same length is about 360 pixels at 300 dpi and about 86.4 pt. These are CSS and print references, not the physical resolution of the screen.

Missing 1.2 in by 1 mm is an error of 3.28 percent. Seat the object on the zero line and look straight down; a slanted glance makes the mark look longer.

Compare it with 1 inch, which is 25.4 mm. This mark is 5.08 mm longer.

  1. 1. Find 0 at the top of the left ruler.
  2. 2. Each long mark is 1 inch. The medium mark halfway is 1/2 inch. The shortest gap is 1/16 inch.
  3. 3. Follow the marks until you reach 1.2 inches.
  4. 4. Rest the object on zero and compare the other edge with that mark.

The length in numbers

Centimetres
3.048 cm
Millimetres
30.48 mm
Inches and nearest fraction
1.2 in · 1 3/16
Place on the ruler
at the 1 3/16 inch division
Millimetres from zero
30
Share of 1 metre
3.05 percent
CSS pixels (96 dpi)
115.2
Points
86.4
Share of a 1 mm miss
3.28 percent

How many times it fits

ObjectReferenceTimesLeft over
the length of an AA battery5.05 cm12 cm
the long side of a bank card8.56 cm224.64 mm
the short side of A4 paper21 cm62.71 cm
1 metre100 cm3224.64 mm

Conversion

UnitValue
Centimetres3.048 cm
Millimetres30.48 mm
Inches1.2 in

Half, double, and neighbours

If the ruler is not true to size, open calibration.

Questions

Where is 1.2 inches on a ruler on a ruler?

1.2 inches on a ruler is 3.048 cm, 30.48 mm and 1.2 inches from zero. The blue line on the left ruler ends at that length.

What is 1.2 inches on a ruler in the other units?

1.2 inches on a ruler equals 3.048 cm = 30.48 mm.

Is 1.2 inches on a ruler true to size on the screen?

After you match a card, the blue line is that real length on this screen. A browser cannot read physical millimetres, so the first scale is only an estimate. Keep zoom at 100%.

How many pixels is 1.2 in?

In CSS, 1 inch is 96 pixels. 1.2 in is about 115.2 pixels. The same length is about 360 pixels at 300 dpi and about 86.4 pt. These are CSS and print references, not the physical resolution of the screen.

Does 1.2 in fit on a 15 cm ruler?

1.2 in fits on a 15 cm school ruler. The spare length is 11.95 cm on a 15 cm ruler, 16.95 cm on a 20 cm ruler, and 26.95 cm on a 30 cm ruler.

How large is a 1 mm miss when reading 1.2 in?

Missing 1.2 in by 1 mm is an error of 3.28 percent. Seat the object on the zero line and look straight down; a slanted glance makes the mark look longer.

Make the ruler true to size

A browser cannot read how many centimetres your screen is. The first scale is an estimate. When the frame matches a bank card, the marks become real length on this display.

Line up the long edge of the card with the width of the frame. The height is only a visual ratio.

ID-1 card